Stoppani Stopdeck
FIller 2K epoxy filler with light extender for decks. Suitable for levelling large boat surfaces, especially decks. Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
Filler 1K filler based on synthetic resins. Especially indicated for low film thickness knifing applications on large surfaces. Used for 1K paint processes.
Ready for use | 4 h at 20°C |
Knifing application |
0-300 μ |
24 h at 20°C |
P80 |
Description
Filler
1K filler based on synthetic resins. Especially indicated for low film thickness knifing applications on large surfaces. Used
for 1K paint processes.
Colour
White.
Characteristics
· Good adhesion
· Fast drying
· Good sanding
Specific weight (part A): 2,21 ± 0,02 g/ml
Substrate preparation
Stoppani 1K primers
Dry sanding with P 280-320 paper
Old coatings
Dry sanding with P 120-180 paper
Application
Knifing.
The product in its original can is covered with an antioxidant solution. This antioxidant solution allows you to store the
product unaltered for a long period of time. Do not mix the product with this solution, it could form specks. Remove this
antioxidant solution and replace it again just for the product’s storage.
Ready for use 4 h at 20°C Knifing
application
0-300 μ 24 h at 20°C P80
P120
S25030 STOPMASTIC 520
S132-G
Mixing ratio
READY FOR USE
N° of knifing: 1 + 1 of refinish
Recommended film thickness: no more than 300 μ each coat,
Interval between coats: 4 h
Drying
10°C |
20°C |
35°C | |
Sanding after | min. 48h | min. 24h | min. 48h |
TECHNICAL DATA SHEET N° S132-GB
UDATED 06/2015
All information contained in this data sheet is the result of carefully controlled tests and is correct to the best of Lechler’s knowledge at the time of issue.
Since conditions of use are beyond the control of the manufacturer, information contained herein is without warranty, implied or otherwise, and final
determination of the suitability of any information or material for the use contemplated and the manner of use is the sole responsibility of the user. FOR
PROFESSIONAL USE ONLY.
FIller 2K epoxy filler with light extender for decks. Suitable for levelling large boat surfaces, especially decks. Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
2K epoxy filler with high film thickness. Its lightness allows you to shape surfaces without jeopardising the boat’s final weight. It features excellent adhesion and flexibility and is especially suitable for filling large surface imperfections. Usable in the yacht field both above and under the waterline. Suitable for steel, aluminium, fibreglass...
2K epoxy filler with low specific weight for high film thickness applications in the yachting sector. It’s useable both above and under the waterline. Its excellent adhesion and flexibility characteristics make it suitable for levelling large surfaces suitably prepared and made of steel, aluminium, fibreglass, carbon fibre and wood. Colour The...
2K epoxy filler for finishing knifing coats. It has a fine grain and can be used for thin knifing coats aimed at closing porosity of epoxy fillers with light extender and at preparing surfaces for Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
Two-component putty for waterproof and repair small holes, nicks or scratches on glass fibers or gelcoat. The package contains the gelcoat, the hardener and a practical spatula for the application. Neutral white colour, paintable with any paint marina. Convenient for quick repairs on any fiberglass surface. Contains styrene datasheet in the attached...
Epoxy thinner for the spray and brush application of epoxy products.