Stoppani Epoxy Thinner
Epoxy thinner for the spray and brush application of epoxy products.
2K epoxy filler for finishing knifing coats. It has a fine grain and can be used for thin knifing coats aimed at closing porosity of epoxy fillers with light extender and at preparing surfaces for
Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
1000 ml |
24 h at 20°C |
Knifing application |
0-300µ |
24h at 20°C |
P 120 |
Description
FIller
2K epoxy filler for finishing knifing coats. It has a fine grain and can be used for thin knifing coats aimed at closing porosity of epoxy fillers with light extender and at preparing surfaces for the following painting step.
Colour
Grey.
Characteristics
·Good flexibility ·
Very good impermeability
· High multipurpose use
· Fast drying
Typical data
Specific weight A and B: 1,54 g/ml
Shore hardness D: 55
Substrate preparation
Stoppani epoxy primers
Dry sanding with P 280-320 paper
Stoppani epoxy fillers
Dry sanding with P 80-120 paper
Application
Knifing.
Application conditions:
- Relative humidity < 80%
- Temperature >10 °C <35°C
- Substrate temperature 5° > dew point
S25005 STOPDECK
S152-GB
Mixing ratio
Volume | Weight | |
S25051 PLASTER FINISHER GREY SOL A | 1000 ml | 1000 g |
S25052 PLASTER FINISHER GREY SOL B | 1000 ml | 1000 g |
Pot life at 20°C: 60’
N° of knifing: 1+1 of refinish, if necessary
Recommended film thickness: up to 300 µ
Theoretical coverage A + B: 3,3 m2 for 1lt mixture at 300µ dry film thickness
Rises in temperature cause pot-life reduction
Drying
10°C |
20°C |
35°C | |
Sanding after | min. 48h | min. 24h | min. 12h |
TECHNICAL DATA SHEET N° S198-GB
UPDATED 04/2011
All information here included is the result of carefully controlled tests and expresses our best and up to date knowledge. This news is given only as an
information, so the firm cannot be accountable for further results. Furthermore it cannot be used as a contestation related to the use of the described
product. All this is due to the fact that use conditions are not under our control
Epoxy thinner for the spray and brush application of epoxy products.
FIller 2K epoxy filler with light extender for decks. Suitable for levelling large boat surfaces, especially decks. Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
Two-component putty for waterproof and repair small holes, nicks or scratches on glass fibers or gelcoat. The package contains the gelcoat, the hardener and a practical spatula for the application. Neutral white colour, paintable with any paint marina. Convenient for quick repairs on any fiberglass surface. Contains styrene datasheet in the attached...
2K epoxy filler with high film thickness. Its lightness allows you to shape surfaces without jeopardising the boat’s final weight. It features excellent adhesion and flexibility and is especially suitable for filling large surface imperfections. Usable in the yacht field both above and under the waterline. Suitable for steel, aluminium, fibreglass...
2K epoxy filler with low specific weight for high film thickness applications in the yachting sector. It’s useable both above and under the waterline. Its excellent adhesion and flexibility characteristics make it suitable for levelling large surfaces suitably prepared and made of steel, aluminium, fibreglass, carbon fibre and wood. Colour The...
Filler 1K filler based on synthetic resins. Especially indicated for low film thickness knifing applications on large surfaces. Used for 1K paint processes.