Stoppani Stopmastic 520
Filler 1K filler based on synthetic resins. Especially indicated for low film thickness knifing applications on large surfaces. Used for 1K paint processes.
2K epoxy filler with high film thickness. Its lightness allows you to shape surfaces without jeopardising the boat’s final weight.
It features excellent adhesion and flexibility and is especially suitable for filling large surface imperfections.
Usable in the yacht field both above and under the waterline.
Suitable for steel, aluminium, fibreglass and stabilised wood, suitably primed.
The balanced viscosity of part A and of part B facilitates product mixing and workability.
Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Under the waterline | Above the waterline
1000 ml | Knifing application |
0-2 cm | 24h at 20°C |
P 80 P 120 |
Description
Filler
2K epoxy filler with high film thickness. Its lightness allows you to shape surfaces without jeopardising the boat’s final weight. It features excellent adhesion and flexibility and is especially suitable for filling large surface imperfections. Usable in the yacht field both above and under the waterline.
Suitable for steel, aluminium, fibreglass and stabilised wood, suitably primed.
The balanced viscosity of part A and of part B facilitates product mixing and workability.
Colour
The mixed product is aquamarine-turquoise
S25093 Plaster 5000 H.P. SOLUZIONE A - yellow
S25094 Plaster 5000 H.P. SOLUZIONE B - blue
Characteristics
· Easy mixing
· Excellent elasticity
· Low specific weight
· Good vertical hold
· Good sanding
Specific weight: 0,60 ± 0,05 g/ml
Hardness shore D > 47
Substrate preparation
Stoppani epoxy primers
Dry sand with p 280-320 paper
Application
Knifing.
Avoid applications at temperatures below 10°C and above 35°C.
At low temperatures avoid environments with high humidity, as a superficial sticky layer could form, making sanding difficult.
Mixing ratio
Volume | |
S25093 PLASTER 5000 H.P. PART A | 1000 ml |
S25094 PLASTER 5000 H.P. PART B | 1000 ml |
N° of knifing: 1+1 of refinish
Recommended film thickness: not over 2cm per layer
Theoretical coverage A + B : 0,2 m2 for 1l at 5 mm film thickness
Interval between coats: min. 24 h at 20°C
Drying
10°C | 20°C | 35°C | |
Time of use of the mixture * | 90’ | 60’ | 30’ |
Sanding after | min. 48 h | min. 24 h | min. 12 h |
Through-drying | 8 days | 4 days | 2 days |
*The time of use is affected by the product volume prepared; larger quantities get warmer and have a shorter usage time. It is recommended to expand the product mass prepared, so as to increase its surface and to facilitate its cooling.
** At low temperatures the product has a higher viscosity; to make it more workable, warm up the single components by a few minutes immersion in hot water before mixing.
TECHNICAL DATA SHEET N° S211-GB
UPDATED 09/2014
All information contained in this data sheet is the result of carefully controlled tests and is correct to the best of Lechler’s knowledge at the time of issue. Since conditions of use are beyond the control of the manufacturer, information contained herein is without warranty, implied or otherwise, and final determination of the suitability of any information or material for the use contemplated and the manner of use is the sole responsibility of the user. FOR PROFESSIONAL USE ONLY.
Filler 1K filler based on synthetic resins. Especially indicated for low film thickness knifing applications on large surfaces. Used for 1K paint processes.
2K epoxy filler for finishing knifing coats. It has a fine grain and can be used for thin knifing coats aimed at closing porosity of epoxy fillers with light extender and at preparing surfaces for Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
Epoxy thinner for the spray and brush application of epoxy products.
FIller 2K epoxy filler with light extender for decks. Suitable for levelling large boat surfaces, especially decks. Wood | Fibreglass | Steel | Aluminium | Fillers | Two-pack | Above the waterline
Two-component putty for waterproof and repair small holes, nicks or scratches on glass fibers or gelcoat. The package contains the gelcoat, the hardener and a practical spatula for the application. Neutral white colour, paintable with any paint marina. Convenient for quick repairs on any fiberglass surface. Contains styrene datasheet in the attached...
2K epoxy filler with low specific weight for high film thickness applications in the yachting sector. It’s useable both above and under the waterline. Its excellent adhesion and flexibility characteristics make it suitable for levelling large surfaces suitably prepared and made of steel, aluminium, fibreglass, carbon fibre and wood. Colour The...